Exhaust system..Who's got what ?

brownie · Post by **brownie** » Mon Mar 12, 2012 10:25 pm

Show and tell what you got,Homemade,Custom Built or off the shelf.
I'll get the ball rolling.
4 systems to choose from,Finally put the Maxum/Corn*s system on.
Wicked sound ,noisy without being loud and booming,wicked cackle on over run.
2.5" all the thru,with Cat built onto it ,Found out these are worth a bomb,Hand built out of Japan.
Other choice's i had;
Standard with wanky tip.
St Mays shot gun system
Racing Beat by RS*R

The RB system was going to be my second choice if i didn't like the corn*s system sound,But i do

Growler · Post by **Growler** » Mon Mar 12, 2012 11:02 pm

Mine is custom. I removed the cat and replaced it with a straight through expansion box/muffler. I increased the pipe diameter to 2" (Did think of 2 1/4" but was concerned about losing too much back pressure). The rear muffler is a V8 Commodore. I wanted to muffle the sound but not hinder the flow.
I'm happy with the sound and increase in performance (in the higher rev range).
I have a set of 4 - 2 - 1 headers to put on it at some stage.
Its slow work in progress as I never have much time to work on cars these days.

Born_disturbed · Post by **Born_disturbed** » Tue Mar 13, 2012 10:25 am

I am running (assuming nothing had been changed before i got it) full factory piping with a straight pipe for the cat and a mazdaspeed tip

Can be a bit loud but I am still happy with it, do want to get a full proper set up eventually

Angreal · Post by **Angreal** » Tue Mar 13, 2012 11:41 am

Maximworks 4-2-1 header with hpc, RB mid-pipe in transit and a Mazdaspeed tip thing. Sounded a lot nicer prior to having my cat chopped out hence the mid-pipe

Kieran · Post by **Kieran** » Tue Mar 13, 2012 1:11 pm

Ive got a fujitsubo fgk rear axle back with the stock midpipe its a great hand made japanese muffler but...
I want an rs*r!!

brownie · Post by **brownie** » Tue Mar 13, 2012 5:10 pm

This is a Racing Beat ,Made by RS*R.
And yes i could be persuaded to part with it.
But it is to suit a NA 1600

Kieran · Post by **Kieran** » Tue Mar 13, 2012 5:31 pm

Nah racing beat is from the usa this is a rs*r
http://rev9autosport.com/nb/engine/rs-r ... xhaust.htm

Where abouts on the exhuast is the rs*r badge?

brownie · Post by **brownie** » Wed Mar 14, 2012 5:05 pm

Nope RS*R made Racing Beat under license in Japan,I,ve had it all checked out.
dumbfounded me too.

Kieran · Post by **Kieran** » Wed Mar 14, 2012 5:48 pm

Well thats wierd never heard of that
The rs*r i want is the exmag gt2 i think its called

sprsta · Post by **sprsta** » Wed Mar 14, 2012 7:03 pm

i had a 3" system with mandrel bends etc. a flow master at the back and a reso from chase

made it all on the floor of my garage

i dont think ill do another one without a hoist

Blues Boy · Post by **Blues Boy** » Wed Mar 14, 2012 10:22 pm

I've got a RS*R 4-2-1 header and a Autoexe cat-back... It's perfect for me... pretty tame while cruising, but has a nice sound when you give it some throttle...

Born_disturbed · Post by **Born_disturbed** » Wed Mar 14, 2012 10:47 pm

That looks real nice and clean, i like that

thebears · Post by **thebears** » Sat Mar 17, 2012 11:38 am

Blues Boy wrote:I've got a RS*R 4-2-1 header and a Autoexe cat-back... It's perfect for me... pretty tame while cruising, but has a nice sound when you give it some throttle...

I like

m4vr1k · Post by **m4vr1k** » Sun Mar 18, 2012 1:54 pm

I have a very special exhaust on the Mazdarati.
It is completely factory, with the optional heat shields that trap stones and rattle really loudly on acceleration. And deceleration. And idle. Also it hits my rear brace, making a fun "clunk" every time you get off the gas.....
However, once I get into the turbo build, I will be replacing it with a 2.5 inch mandrel bent system from my local exhaust stop. 3 inch just seems a little excessive, and I want to keep the volume too.

Exhaust system..Who's got what ?

Exhaust system..Who's got what ?

Who is online